Acroprint Barcode Reader ATR20 20 User Manual

ATR20/20 Quick Start RS485 Communications  
Cable connections  
on the computer &  
ADCT  
Before you begin  
You’ll need the following hardware:  
RS485 Wiring  
diagram  
RS485 to RS232 Converter Assembly  
Junction boxes (minimum of 2 plus one box for  
each additional terminal)  
The RS485 Serial port is  
located on the left corner  
of the terminal. RS485 is  
imprinted on the terminal  
Remove cover to expose ADCT ports  
Route the RS485 and power cables behind the  
wall bracket.  
Secure the wall bracket with the supplied  
screws to a hard surface such as plywood.  
Mount the ADCT to the wall bracket.  
Modular cable (minimum of 2 plus one cable  
for each additional terminal)  
Teflon Cable (lengths available: 100', 200', 500',  
1000')  
Acroprint Data Collection Terminal (ADCT)  
including,  
casing.  
A
RS485 communication  
allows up to 32 terminals  
to be connected to one  
serial port. An RS232  
port on the host PC is  
used with an  
Power Supply  
Wall Mount and 4 screws  
Configuration Badge  
RS-232/RS485 converter  
to complete the  
Follow the setup instructions on this Quick Start  
sheet. For updates to the ATR20/20 documenta-  
tion and last-minute product information, visit  
connection.  
B
RS485 provides good  
protection from interfer-  
ence over long runs up to  
4000 feet.  
NOTE: When wiring a  
network, always follow  
the electric wiring codes  
in your area. Typically, a  
telfon coated wire is  
required for wiring  
A
through a ceiling. The  
junction box to junction  
box wire shown is a  
B
teflon jacketed cable.  
Connect RS485 to  
the ADCT  
Connect power  
Connect RS485 to  
RS232 converter  
assembly to PC  
serial port  
Setup terminal  
supply to the ADCT.  
Then plug into the  
wall.  
Swipe the  
configuration badge  
and select the desired  
option:  
Option 1 Date and  
Time  
Select DDMMYYY  
Select HHMM  
Option 2 Ports  
Connect the RS485 to RS232 converter  
assembly to the PC's 9 pin serial port. Connect  
the RJ11 modular cable between the junction  
box and the converter assembly. If your  
computer has a 25-pin  
serial port, you will  
need a 9-pin male to  
25-pin female null  
Select RS485 Communications  
(Default)  
modem adaptor,  
available through  
most computer stores.  
Select 9600 Speed (Default)  
Select Parallel Printer Port (Default)  
Transaction Timeout = 0  
Terminal ID = 1 (Default)  
*Multiple terminals require different  
terminal ID's.  
Option 3 Readers  
Make sure the power is off at both the time clock  
terminal and the PC, and the access door on the  
terminal is removed.  
1 - Internal barcode 3 of 9 (Default)  
2 - External barcode 3 of 9 (Default)  
3 - Magnetic stripe Track 2 (Default)  
Option Test  
1 - Signals  
2 - Print  
Using the supplied cable, connect the RJ-11  
modular connector to the ADCT RS485 port on the  
lower left corner and the other end to the junction  
box.  
Connect the power supply to the ADCT.  
Replace access door cover. Connect the  
power supply transformer to the wall power  
outlet. Observe proper supply voltage.  
cable runs to junction box  
Repeat for each ADCT terminal.  
Attach security key  
to PC's parallel  
printer port  
Before you begin the  
software installation,  
you need the following  
The Wizard Setup  
Software installation  
Click on the ATR20/20 ICON on the desktop  
a) Insert Software ATR20/20 into your CD-  
ROM drive.  
b) On the Install Menu Click on Software  
To login type sysop for user and password for  
password.  
Connect the software security key to a work-  
ing PC parallel printer port. If the PC parallel  
port has a printer cable attached, remove the  
printer cable from the PC and attach the  
software security key. Reattach the printer  
cable to the software key.  
ATR20/20 Software on CD  
A software security key.  
Install  
If the install menu does not appear,  
click Start on the taskbar, select Run,  
type D:\Disk1\Setup.exe (where D is  
your CD's drive letter), then click OK.  
Follow the instructions on the screen.  
ATR 20/20  
The wizard will guide you through the complete  
setup of the program.  
software key  
06-0268-001 Rev. A  
 

3Com Switch DUA1750 2BAA01 User Manual
3M Landscape Lighting M5560 User Manual
Ace Home Theater Server LHD LIMITED II User Manual
Adesso Computer Keyboard ACK 730PB User Manual
Agilent Technologies Tablet Accessory 83480A User Manual
Alesis DVR ALESIS M20 User Manual
Allied Telesis Network Card AT 2874SX User Manual
Amana Range AER5845RAW User Manual
American Standard Indoor Furnishings 0495221 User Manual
Axor Outdoor Shower 27426XX1 User Manual